Drag Mouse Over The Image To Zoom View.
Description
VURA FasTile (C1 T)
TILE ADHESIVE FOR GRES &
CERAMIC TILES
CERAMIC TILES
Polymer fibre modified grey cement based adhesive with no vertical slip, suitable for fixing ceramic and gres tiles for floors and walls in internal applications.
CHARACTERISTICS
- C1 T compliant with EN 12004 standard
- Type 1 T as per IS 15477-2019
- For ceramic and gres tiles adhesive
- No vertical slip
- Application upto 10mm
- Prolonged workability
- Adjustable
- Excellent workability
- For larger vitrified tiles up to 4 sq.ft.
Documents & Downloads
Usage Guide
SUBSTRATE PREPARATION
Adhesive can be applied on even and compact substrates, free of any substances that reduce adherence (grease, bitumen, oil, paint, dust etc.). Concrete should be at least 1 month old. Cement screeds and plasters should be fully cured. Anhydrite (residual moisture below 0.5%) substrates should be mechanically roughened and cleaned from dust. Aerated concrete should be free from dust. Substrates must not be wet. Any existing dirt, loose layers and paint coating shall be mechanically removed. Absorbent substrates shall be dampen and remove excess water before application.
APPLICATION
Pour VURA FasTile into a container with the precisely measured amount of clean water and stir with a drill and mixer until a homogeneous mass without lumps is obtained. Leave for 5 min. and then stir again. Apply the mortar with a suitable notched trowel. Use the proper sized notch trowel to ensure full bedding in the tile. Do not soak tiles adhesive in the water. The back buttering method shall be used for larger tiles and for outdoor applications (ie. additionally a thin layer of the mortar should be spread on the tile's back side, contact area > 90%). Place the tiles only during the open time of the adhesive. Fresh excess mortar can be removed with water, hardened material can only be removed mechanically. Grouting on the wall can be done after 8 hrs in (Gres tiles) and after 24 hrs in porous tiles using VURA grouts. Floors are set to light traffic after approx. 24 hrs. Expansion joints, joints at the corners of walls and floor and around sanitary equipment shall be filled with sealants or shall be treated with appropriate treatment.
Description
VURA FasTile (C1 T)
TILE ADHESIVE FOR GRES &
CERAMIC TILES
CERAMIC TILES
Polymer fibre modified grey cement based adhesive with no vertical slip, suitable for fixing ceramic and gres tiles for floors and walls in internal applications.
CHARACTERISTICS
- C1 T compliant with EN 12004 standard
- Type 1 T as per IS 15477-2019
- For ceramic and gres tiles
- No vertical slip
- Application upto 10mm
- Prolonged workability
- Adjustable
- Excellent workability
- For larger vitrified tiles up to 4 sq.ft.
Usage Guide
SUBSTRATE PREPARATION
Adhesive can be applied on even and compact substrates, free of any substances that reduce adherence (grease, bitumen, oil, paint, dust etc.). Concrete should be at least 1 month old. Cement screeds and plasters should be fully cured. Anhydrite (residual moisture below 0.5%) substrates should be mechanically roughened and cleaned from dust. Aerated concrete should be free from dust. Substrates must not be wet. Any existing dirt, loose layers and paint coating shall be mechanically removed. Absorbent substrates shall be dampen and remove excess water before application.
APPLICATION
Pour VURA FasTile into a container with the precisely measured amount of clean water and stir with a drill and mixer until a homogeneous mass without lumps is obtained. Leave for 5 min. and then stir again. Apply the mortar with a suitable notched trowel. Use the proper sized notch trowel to ensure full bedding in the tile. Do not soak tiles in the water. The back buttering method shall be used for larger tiles and for outdoor applications (ie. additionally a thin layer of the mortar should be spread on the tile's back side, contact area > 90%). Place the tiles only during the open time of the adhesive. Fresh excess mortar can be removed with water, hardened material can only be removed mechanically. Grouting on the wall can be done after 8 hrs in (Gres tiles) and after 24 hrs in porous tiles using VURA grouts. Floors are set to light traffic after approx. 24 hrs. Expansion joints, joints at the corners of walls and floor and around sanitary equipment shall be filled with sealants or shall be treated with appropriate treatment.
