Drag Mouse Over The Image To Zoom View.
Description
VURA FasTone (C2 T E)
Elastic Universal
Universal fibre modified, Thin bed and middle bed adhesive for application of ceramic tiles, vitrified tiles and natural stone on wall & floor in internal and external application.
CHARACTERISTICS
- C2 TE compliant with EN12004 standard
- Type 3 T as per IS 15477-2019
- For ceramic, vitrified (semi and fully) tiles, glass mosaic and natural stone (non-sensitive)
- On balconies, terraces, wet rooms, bathrooms and swimming pools
- On water proof and moisture proof layers
- For large and small tiles
- For inside and outside use
- Longer open time for safer application
- Easy and excellent workability thanks to plastified consistency
- Application Upto 10mm
- Adjustable
- For Tile on Tile application
- No vertical slip
Documents & Downloads
Usage Guide
SUBSTRATE PREPARATION
Adhesive can be applied on even and compact substrates, free of any substances that reduce adherence (grease, bitumen, oil, paint, dust etc.). Concrete should be at least 1 month old. Cement screeds and plasters should be fully cured. Anhydrite (residual moisture below 0.5%), gypsum (residual moisture below 1%) substrates should be mechanically roughened and cleaned from dust. Aerated concrete should be free from dust. Can be applied on existing tiles and should be roughened and cleaned before application. Substrates must not be wet. Any existing dirt, loose layers and paint coating shall be mechanically removed. Absorbent substrates shall be dampen and remove excess water before application.
APPLICATION
Pour VURA FasTone into a container with the precisely measured amount of clean water and stir with a drill and mixer until a homogeneous mass without lumps is obtained. Leave for 5 min. and then stir the mixture again. Apply the mortar with a suitable notched trowel. Use the proper sized notch trowel to ensure full bedding in the tile. The depth of trowel's notching is depends on the size of tile / stone. The back buttering method shall be used for larger tiles / stones and for outdoor applications (ie. additionally a thin layer of the mortar should be spread on the tile/stone's back side, contact area > 90%). Place the tiles/stones only during the open time of the adhesive. Lay the mortar and press while the mortar is still sticky. Fresh excess mortar can be removed with water, hardened material can only be removed mechanically. Grouting can be performed no earlier than after 24 hours using VURA grouts. Floors are set to light traffic after apprx. 24 hrs. Expansion joints, joints at the corners of walls and floor and around sanitary equipment shall be filled with sealants or shall be treated with appropriate treatment
Description
VURA FasTone (C2 T E)
Elastic Universal
Universal fibre modified, Thin bed and middle bed adhesive for application of ceramic tiles, vitrified tiles and natural stone on wall & floor in internal and external application.
CHARACTERISTICS
- C2 TE compliant with EN12004 standard
- Type 3 T as per IS 15477-2019
- For ceramic, vitrified (semi and fully) tiles, glass mosaic and natural stone (non-sensitive)
- On balconies, terraces, wet rooms and bathrooms
- On water proof and moisture proof layers
- For large and small tiles
- For inside and outside use
- Longer open time for safer application
- Easy and excellent workability thanks to plastified consistency
- Application Upto 10mm
- Adjustable
- For Tile on Tile application
- No vertical slip
Usage Guide
SUBSTRATE PREPARATION
Adhesive can be applied on even and compact substrates, free of any substances that reduce adherence (grease, bitumen, oil, paint, dust etc.). Concrete should be at least 1 month old. Cement screeds and plasters should be fully cured. Anhydrite (residual moisture below 0.5%), gypsum (residual moisture below 1%) substrates should be mechanically roughened and cleaned from dust. Aerated concrete should be free from dust. Can be applied on existing tiles and should be roughened and cleaned before application. Substrates must not be wet. Any existing dirt, loose layers and paint coating shall be mechanically removed. Absorbent substrates shall be dampen and remove excess water before application.
APPLICATION
Pour VURA FasTone into a container with the precisely measured amount of clean water and stir with a drill and mixer until a homogeneous mass without lumps is obtained. Leave for 5 min. and then stir the mixture again. Apply the mortar with a suitable notched trowel. Use the proper sized notch trowel to ensure full bedding in the tile. The depth of trowel's notching is depends on the size of tile / stone. The back buttering method shall be used for larger tiles / stones and for outdoor applications (ie. additionally a thin layer of the mortar should be spread on the tile/stone's back side, contact area > 90%). Place the tiles/stones only during the open time of the adhesive. Lay the mortar and press while the mortar is still sticky. Fresh excess mortar can be removed with water, hardened material can only be removed mechanically. Grouting can be performed no earlier than after 24 hours using VURA grouts. Floors are set to light traffic after apprx. 24 hrs. Expansion joints, joints at the corners of walls and floor and around sanitary equipment shall be filled with sealants or shall be treated with appropriate treatment
