Drag Mouse Over The Image To Zoom View.
Description
VURA FasTone S2 (C2 T E S2)
S2 Premium Flexible
Highly flexible, polymer fibre modified special adhesive mortar for installing vitrified and natural stone slabs with high safety reserves.
CHARACTERISTICS
- C2 TE S2 compliant with EN 12004 standard
- Type 4 T S2 as per IS 15477-2019
- For use on difficult substrates
- For tile and stones of size more than 1200 x 1200 mm
- For indoor and outdoor use
- Application up to 15mm
Documents & Downloads
Usage Guide
SUBSTRATE PREPARATION
VURA FasTone S2 adheres to all sound, load-bearing, clean, dry and damp substrates free of substances which may impair adhesion. Remove coatings of insufficient bearing strength.
Indoor use:
Use SuPrima to prime calcium sulphate screeds (gypsum/anhydrite screeds, mechanically roughened and freed from dust, residual moisture: ≤0.5 %, heated screeds ≤0.3 %), cellular concrete and other absorbent substrates.
Prime the non absorbent substrates, tiles, natural/artificial stone floors and firmly adhering coatings.
Outdoor and indoor use:
Plasters of mortar groups P II and P Ill (at least 14 days old), cement screeds (at least 28 days old, residual moisture < 2 %, heated screeds < 1 .8 %) and in-situ concrete (at least 28 days old) can be directly covered with tiles / stones.
APPLICATION
Mix VURA FasTone S2 with clean, clear water and stir until the mixture is completely free of lumps. Leave the mortar to mature for approx. 5 minutes and then stir again. If necessary, add small amounts of water until the desired consistency is reached.
Apply FasTone S2 according to the generally recognized rules of the thin-bed resp. mediumbed method or use the buttering-floating method. Allow for a skin formation time of approx. 40 minutes.
Use a trowel with a suitable notch size to ensure cavity free placement of the tiles and slabs. After the pot life has expired and the mortar begun to set, do not attempt to re-temper the mortar by adding water and stirring again.
Description
VURA FasTone S2 (C2 T E S2)
S2 Premium Flexible
Highly flexible, polymer fibre modified special adhesive mortar for installing vitrified and natural stone slabs with high safety reserves.
CHARACTERISTICS
- C2 TE S2 compliant with EN 12004 standard
- Type 4 T S2 as per IS 15477-2019
- For use on difficult substrates
- For tile and stones of size more than 1200 x 1200 mm
- For indoor and outdoor use
- Application up to 15mm
Usage Guide
SUBSTRATE PREPARATION
VURA FasTone S2 adheres to all sound, load-bearing, clean, dry and damp substrates free of substances which may impair adhesion. Remove coatings of insufficient bearing strength.
Indoor use:
Use SuPrima to prime calcium sulphate screeds (gypsum/anhydrite screeds, mechanically roughened and freed from dust, residual moisture: ≤0.5 %, heated screeds ≤0.3 %), cellular concrete and other absorbent substrates.
Prime the non absorbent substrates, tiles, natural/artificial stone floors and firmly adhering coatings.
Outdoor and indoor use:
Plasters of mortar groups P II and P Ill (at least 14 days old), cement screeds (at least 28 days old, residual moisture < 2 %, heated screeds < 1 .8 %) and in-situ concrete (at least 28 days old) can be directly covered with tiles / stones.
APPLICATION
Mix VURA FasTone S2 with clean, clear water and stir until the mixture is completely free of lumps. Leave the mortar to mature for approx. 5 minutes and then stir again. If necessary, add small amounts of water until the desired consistency is reached.
Apply FasTone S2 according to the generally recognized rules of the thin-bed resp. mediumbed method or use the buttering-floating method. Allow for a skin formation time of approx. 40 minutes.
Use a trowel with a suitable notch size to ensure cavity free placement of the tiles and slabs. After the pot life has expired and the mortar begun to set, do not attempt to re-temper the mortar by adding water and stirring again.
